Skip to content

Sub-GHz RF โ€‹

Learn AWS hacking from zero to hero with htARTE (HackTricks AWS Red Team Expert)!

Other ways to support HackTricks:

Garage Doors โ€‹

Garage door openers typically operate at frequencies in the 300-190 MHz range, with the most common frequencies being 300 MHz, 310 MHz, 315 MHz, and 390 MHz. This frequency range is commonly used for garage door openers because it is less crowded than other frequency bands and is less likely to experience interference from other devices.

Car Doors โ€‹

Most car key fobs operate on either 315 MHz or 433 MHz. These are both radio frequencies, and they are used in a variety of different applications. The main difference between the two frequencies is that 433 MHz has a longer range than 315 MHz. This means that 433 MHz is better for applications that require a longer range, such as remote keyless entry.
In Europe 433.92MHz is commonly used and in U.S. and Japan it's the 315MHz.

Brute-force Attack โ€‹

If instead of sending each code 5 times (sent like this to make sure the receiver gets it) so just send it once, the time is reduced to 6mins:

and if you remove the 2 ms waiting period between signals you can reduce the time to 3minutes.

Moreover, by using the De Bruijn Sequence (a way to reduce the number of bits needed to send all the potential binary numbers to burteforce) this time is reduced just to 8 seconds:

Example of this attack was implemented in https://github.com/samyk/opensesame

Requiring a preamble will avoid the De Bruijn Sequence optimization and rolling codes will prevent this attack (supposing the code is long enough to not be bruteforceable).

Sub-GHz Attack โ€‹

To attack these signals with Flipper Zero check:

Rolling Codes Protection โ€‹

Automatic garage door openers typically use a wireless remote control to open and close the garage door. The remote control sends a radio frequency (RF) signal to the garage door opener, which activates the motor to open or close the door.

It is possible for someone to use a device known as a code grabber to intercept the RF signal and record it for later use. This is known as a replay attack. To prevent this type of attack, many modern garage door openers use a more secure encryption method known as a rolling code system.

The RF signal is typically transmitted using a rolling code, which means that the code changes with each use. This makes it difficult for someone to intercept the signal and use it to gain unauthorised access to the garage.

In a rolling code system, the remote control and the garage door opener have a shared algorithm that generates a new code every time the remote is used. The garage door opener will only respond to the correct code, making it much more difficult for someone to gain unauthorised access to the garage just by capturing a code.

Basically, you listen for the button and capture the signal whilst the remote is out of range of the device (say the car or garage). You then move to the device and use the captured code to open it.

An attacker could jam the signal near the vehicle or receiver so the receiver cannot actually โ€˜hearโ€™ the code, and once that is happening you can simply capture and replay the code when you have stopped jamming.

The victim at some point will use the keys to lock the car, but then the attack will have recorded enough "close door" codes that hopefully could be resent to open the door (a change of frequency might be needed as there are cars that use the same codes to open and close but listens for both commands in different frequencies).

โš ๏ธ

Jamming works, but it's noticeable as if the person locking the car simply tests the doors to ensure they are locked they would notice the car unlocked. Additionally if they were aware of such attacks they could even listen to the fact that the doors never made the lock sound or the cars lights never flashed when they pressed the โ€˜lockโ€™ button.

Code Grabbing Attack ( aka โ€˜RollJamโ€™ ) โ€‹

This is a more stealth Jamming technique. The attacker will jam the signal, so when the victim tries to lock the door it won't work, but the attacker will record this code. Then, the victim will try to lock the car again pressing the button and the car will record this second code.
Instantly after this the attacker can send the first code and the car will lock (victim will think the second press closed it). Then, the attacker will be able to send the second stolen code to open the car (supposing that a "close car" code can also be used to open it). A change of frequency might be needed (as there are cars that use the same codes to open and close but listens for both commands in different frequencies).

The attacker can jam the car receiver and not his receiver because if the car receiver is listening in for example a 1MHz broadband, the attacker won't jam the exact frequency used by the remote but a close one in that spectrum while the attackers receiver will be listening in a smaller range where he can listen the remote signal without the jam signal.

โš ๏ธ

Other implementations seen in specifications show that the rolling code is a portion of the total code sent. Ie the code sent is a 24 bit key where the first 12 are the rolling code, the second 8 are the command (such as lock or unlock) and the last 4 is the checksum. Vehicles implementing this type are also naturally susceptible as the attacker merely needs to replace the rolling code segment to be able to use any rolling code on both frequencies.

โŒ

Note that if the victim sends a third code while the attacker is sending the first one, the first and second code will be invalidated.

Alarm Sounding Jamming Attack โ€‹

Testing against an aftermarket rolling code system installed on a car, sending the same code twice immediately activated the alarm and immobiliser providing a unique denial of service opportunity. Ironically the means of disabling the alarm and immobiliser was to press the remote, providing an attacker with the ability to continually perform DoS attack. Or mix this attack with the previous one to obtain more codes as the victim would like to stop the attack asap.

References โ€‹

Learn AWS hacking from zero to hero with htARTE (HackTricks AWS Red Team Expert)!

Other ways to support HackTricks: